And that’s why I only play Pokemon TCG. That, and the fact it’s far more affordable than other card games.

I’m not sure I follow

I’m stuck with Facebook because of Messenger, but I’ve deleted everything else

They’re undead, not zombies. They might have been raised from the grave by like, a litch or something and not a zombie virus idk

https://theonion.com/opinion/cartoons/

3D printers are easier to use than getting ink on paper and it’s appalling

Bit discouraging tbh

Had to give it a shot at least

Hey I just saw your update! I’m glad you’re getting better results, but like you mentioned, something is definitely still wrong. I’m still pretty convinced your nozzle is clogged, even though it’s new, and I’ll do my best to explain why!

To start, if your printer wasn’t working normally before you printed in wood, I’m totally wrong about everything below and you can stop reading here!

If your printer was working normally before you tried printing in wood though, that means the e-steps were already calibrated correctly, and they wouldn’t need to be re-calibrated after replacing the hot end. If you had replaced the extruder and it started acting this way, that would be a good reason to re-calibrate the e-steps, but replacing the hot-end shouldn’t have had an impact. After swapping an extruder, you calibrate e-steps to basically teach the printer how to extrude the correct amount of filament in the real world again since the new extruder might have different specs from the original and the printer has no way to know something has changed. A hot-end swap doesn’t necessitate recalibrating e-steps though because the extruder is the same and it’s still going to be pushing the same amount of filament through the printer.

If your nozzle is clogged and you recalibrate the e-steps, the measurements you take will be off since the printer can’t push filament through at the rate it should be able to. Your new benchy looks better than before, but that could be because the higher e-steps you calculated mean the printer is now forcing more filament past the blockage by working the extruder more. It’s been calibrated to compensate for the fact it can’t push filament through fast enough, but it’s working harder to do this and it will severely limit its speed before it starts underextruding again. I’m guessing this is the reason for the 3 hour long benchy at 20mm/s? You shouldn’t need to be at 220 C to get PLA to print at 20mm/s from a 0.4mm nozzle either.

Not all nozzles or hotends are well-made or handled with care at the factory. It’s totally possible you got one that shipped with some sort of tiny unnoticeable debris inside that worked its way down into the nozzle as the filament pushed it along. I have a cheap bag of 0.4mm nozzles that have metal shavings stuck in some of them and your first benchy is exactly what my prints look like when I use one of them. If possible, I still recommend changing the nozzle before doing anything more expensive like replacing the extruder. You’ll probably need to set the e-steps back to what they were before changing them though, otherwise you’ll be extruding too much filament if the new nozzle isn’t clogged and the old one is.

Wow I just looked it up and that is the worst design I’ve ever seen. That’s a ton of work just to replace one of the most commonly changed parts.

The fact it won’t print below 220° makes me think it’s a problem with your hotend, and my best guess is that your nozzle is clogged. The higher temperature might be helping the extruder to squeeze a bit of filament around the clog, but not enough.

Changing the nozzle is quick and easy, and most printers come with a spare or two, so I would give that a shot before diving too deep into diagnostics.

I might be using it wrong, but One Note was king in college and still is for my D&D session notes now too. I never present them to anyone though.

👉⌚
🕳🏃‍♂️💨

Right on schedule ⏳

Things must play out exactly as they currently are to ensure Australia acquires its future time powers. Changing the past would likely make it so that Australia doesn’t eventually come to control the time power in the future but some other country does instead, and thus the past could never have been changed by Australia to prevent bad things from happening, which would again put Australia in control of the time power since the past was never altered. The only possible future is one in which Australia doesn’t fix the past, and all other possibilities self-correct back to this alpha-timeline.

Haha thankfully the first layer really was flawless, but I had to cancel this print for unrelated reasons pretty soon after posting anyways. Turns out I was so excited to finally get printing again, I forgot to re-enable supports in the slicer after the last thing I printed a while ago didn’t need them.

Something I’ve noticed with my computer monitor is that it does this shifting thing. The usable resolution is 1440p, but the screen is actually a slightly higher resolution with maybe 10 extra pixels in each direction that it uses to very slowly bounce the display image around in like a very large DVD player screensaver.

It’s opt-in because it’s a beta

Haha I came here to insult the Samsung keyboard but you’ve already done my job

Sounds like solid life advice tbh